Blue Skies Terrazzo
Powder Blue Terrazzo
Dark Taupe Terrazzo
Aged Marble Terrazzo
Fresh Cream Terrazzo
Vinca Blue Terrazzo
Heavy duty outdoor use
This stair tread is not intended to comply with some aspects of ASTM F2169 as it is not intended for interior use.
Medium duty use
FlexiFlor flash coved
CAUTION: This Epoxy Caulk cannot be removed from surface after it has cured without causing irreparable damage to the product surface. If spilled, remove immediately with a clean cloth and a solution of warm water and detergent.
Clean equipment with a solution of warm water and detergent. To save a partial cartridge of caulk for future use, leave the mixing nozzle and retaining nut in place on the tube. Material will cure inside the nozzle, but not at the base where the nozzle screws onto the cartridge. To use the remainder of the cartridge, remove the old nozzle and replace with a clean nozzle.
1. Be sure underfloor is dry, clean, smooth and free from foreign matter.
2. Pour Part “B” into Part “A” and mix until completely uniform. Bond strength depends on efficient mixing.
3. Do not mix more adhesive than you can spread in 30 minutes. A complete unit of Part “A” and Part “B” should cover approximately 150 square feet per gallon unit.
4. Do not allow mixture of Part “A” and Part “B” to remain in the container longer than 30 minutes. It is best if the mixed adhesive is immediately poured on the floor and troweled.
5. Mix and spread the adhesive at a temperature of approximately 70°F (21°C). Use a trowel with fine notching, (notches 1/16” wide, 1/32” deep and on 1/16” centers). This should cover 150 square feet per gallon unit.
6. Do not place flooring in adhesive too soon. Allow 30 minutes for adhesives to partially set before laying flooring. This prevents flooring from slipping and adhesive oozing through joint or seams.
7. Do not kneel or walk directly on flooring as installation progresses. Kneel on piece of plywood or Masonite.
8. After flooring has been in the adhesive of one hour, cross roll thoroughly with a 100 pound sectional roller. It may be necessary to weight seams until a suitable bond has been established.
9. Do not place heavy furniture or allow heavy traffic until 48 hours after installation.
10. Clean flooring and tools with warm soapy water before adhesive hardens.
1. Flooring materials and adhesives should be stored in a pre-heated building where room and substrate temperature should be no less than 65° F, 24 hours before, during and after installation.
2. Sub-floors must be cleaned, free of dust, dirt, grease, wax, paint, curing or parting agents or any other substances that may affect the bond. Concrete floors must be level, fully cured and free of excessive moisture emissions and alkali. Maximum moisture emissions of 3lbs/1000sf/24hrs ASTM F1869, pH 7.0-9.0. The relative humidity of the substrate should be 75% or less ASTM F2170. Very porous substrates should be primed with a compatible acrylic primer.
3. Trowel recommendations: 1/16 x 1/16 x 1/16 square notch, approximate coverage: 125 – 150sqft per gallon.
4. If sheet goods are to be installed, cut to fit before spreading adhesive. All seems must be overlapped and double cut. Allow the adhesive to tack properly and maintain proper trowel notch and adhesive delivery throughout the entire installation.
5. Lay floorcovering into the adhesive as to minimize air bubbles and wrinkles.
6. Roll flooring with a 75-100lb roller in both north-south and east-west directions to ensure 100% transfer and to remove trapped air.
7. Restrict foot traffic for at least 12 hours and DO NOT move heavy objects on carts over the finished flooring for at least 48 hours.
1. A clean substrate is ESSENTIAL! Thoroughly sweep and vacuum the substrate first. Damp mop to remove any remaining dust or debris. Extra attention to substrate preparation is essential for a successful installation.
2. Shake can well before each use. Point can downwards, press the side of the nozzle tip as you slowly walk back and forth. Do not use a sweeping motion as this may create uneven coverage. Clean up drips. Be sure to achieve full coverage. When using on a non-porous substrate, a lighter application may be necessary.
NOTE: It is up to the end user to determine the coverage that is appropriate for flooring and jobsite conditions. Bond testing prior to the installation will help identify the appropriate application rate, open and working time, and any potential bonding problems to the substrate or flooring. To determine the accurate coverage rate, measure and chalk line the substrate into grids (using the appropriate square feet of area for the adhesive application) and spray the entire can of adhesive onto each measured grid area.
3. Allow the adhesive to dry completely with no transfer to fingers when lightly touched. Open time will vary depending on the adhesive coverage, substrate porosity and the ambient conditions. Working time for the adhesive should not exceed 4 hours.
4. Roll the floor immediately after the installation is complete with the appropriate roller specified for the flooring type. Normal traffic and rolling loads may be allowed as soon as the installation, finishing and clean-up are complete.
Rate of application depends on flooring product being installed and porosity of the substrate. – 150 square feet per can (approximate)
Heavy duty use
abrasive strip colors